Saturday, June 29, 2013

DIY Steering Wheel Cover

The idea to make my own steering wheel cover has been floating around in my head for quite some time.  I don’t like how covers you buy from the store always smell like an auto parts store and end up making the car also smell like an auto parts store.  Plus they are always black or gray or brown, which aren’t exactly the cutest colors out there.

I also wanted a cute new steering wheel cover because I am borrowing my parent’s car while they are living out of the country and I wanted to add some of my own flair to the car.  (I don’t think they would appreciate me slapping some bumper stickers on it, even though that would jazz things up.)  Plus the one already in the car is that pleather material that burns your hands if it’s hot, which it often is.

I never made one, though, because I thought it would be hard to do.  Well I am happy to report that it is not hard at all, and in fact this turned out to be a really quick and easy project.


Check it out!  Cute, soft, unburnable, and free of auto parts store smell.  Success!

Now that you’re super pumped to sew your own steering wheel cover, here’s what you need:


Fabric:  I used cotton fabric.  The amount you need depends on the size of your steering wheel so measure that first.  I also used some fleece to make the cover cushy.

Elastic:  I used ¼ inch elastic. 

First you need to measure your steering wheel, like so:


It was rather difficult to get a shot of this with one hand while trying to hold the tape on with the other hand, but what I do for my readers! 

Make sure your measuring tape is nice an tight so you get the right measurement.  If you make it too long the cover could be baggy.  Add ½” for seam allowance.

You also need to figure out the width of the cover, so measure the steering wheel again like so:


After measuring add ½” to 1” seam allowance, depending on how big your elastic is.

For my steering wheel, the measurements were 40” long and 4 ½” wide (that includes both seam allowances.)

After getting your measurements it’s time to cut out the fabric.  Just cut a single strip in the length and width you need.  Then cut a strip of fleece to the same length, but take ½” off the width.

Next, fold and press the sides of the fabric strip to make a casing for the elastic to go through.  I folded mine over ¼” and another slightly over ¼”.


Pin down and sew the casing on the inner edge.


Next, take the fleece and sew it down to the back of the outer fabric.


If you want to make it extra cushy, sew down a double layer of fleece.

Now it’s time to put in the elastic, which I never enjoy doing.  First, cut two pieces of elastic that are the exact length of your steering wheel, in my case it was 39 ½”. 

Attach a safety pin to both ends of the elastic and start pulling it through the side tube you made earlier.


Once you get it through (hooray!), sew down one end of the elastic to keep it in place.


Repeat on the other side of the cover.

Once both sides have the elastic in, fold the cover in half with right sides facing, and sew the edges together.



Trim it down, the flip it over and sew down a zig-zag for some extra support.



And that is it!  Now all you have to do it pop that baby on your steering wheel and start looking cool!



If it’s too baggy, just sew the ends together further down.  If it’s too tight and doesn’t fit, run back to your sewing room to try again! 

I’m loving this new cover, it makes me smile every time I get in the car.
Hope you it try it out!  Thanks for reading!




18 comments:

  1. I love this! Thanks for sharing! I am excited to give this pattern a try. :)

    ReplyDelete
  2. I love it, too! And good tip on the fleece. I didn't even think of adding cushion.

    ReplyDelete
  3. Great!Really pretty but will any other material look as beautiful as this?

    ReplyDelete
  4. Nice article. I think it is useful and unique article. I love this kind of article and this kind of blog. I have enjoyed it very much. Thanks for your website.
    TLR Carbon wheels

    ReplyDelete
  5. Craig Willows-Keetley shares the story of his journey to compete in the half Ironman length Challenge event in Phuket. Craig shares his training program, details of the race and lessons he learnt from the event. Hear his story about the Challenge event that’s a Challenge and a half!.
    Carbon bike wheels

    ReplyDelete
  6. I tried this pattern yesterday and it works!!. I just loved my new steering wheel cover and thanks a lot. Tomorrow I will try the same thing on a rexin sheet.

    True power wheel cover

    ReplyDelete
  7. A steering wheel is always special to a driver and it is one of the most touched parts of the car by the driver. It is impossible to drive a car without the steering wheel and it should always match with the personality of the car as well as drivers. Heated wheels

    ReplyDelete
  8. This comment has been removed by the author.

    ReplyDelete
  9. Wow, that's great! As smart as a new pin! I really like the car steering wheel cover, of course, if you are too lazy to work, or hands-on ability is too poor, you can also buy finished.

    ReplyDelete
  10. In your instructions it says the fabric should be 40" in length but the picture of you measuring your steering wheel shows the steering wheel is over 40" long?

    ReplyDelete
  11. Made one. Turned out awesome. Thanks

    ReplyDelete
    Replies
    1. I wish I could include a picture.

      Delete
    2. I lined the inside with non slip vinyl.

      Delete
  12. I love this kind of article and this kind of blog. I have enjoyed it very much. Thanks for your website. best steering wheel cover

    ReplyDelete
  13. This comment has been removed by the author.

    ReplyDelete
  14. i like this posted subject .Auto insides are there to be improved, and there's an enormous market out there, so have a ton of fun doing as such! To begin with, you could get situate covers.. best steering wheel cover

    ReplyDelete